The Crawler Store Products

This spot is for companies not on this forum to announce new products. You must be a company owner to post topics here!
Post Reply
User avatar
kevinlongisland
Regular Member
Posts: 172
Joined: Thu Feb 19, 2004 7:09 pm
Location: Phoenix, Arizona
Contact:

The Crawler Store Products

Post by kevinlongisland » Wed Jan 26, 2005 3:56 am

Image

Below are the current offerings from The Crawler Store:

http://www.thecrawlerstore.com

"The Stick" Rock Crawling Chassis. The Stick chassis is one of the most innovative rock crawling designs currently available. It's also the lightest crawler available by at least 60%. Superior full rising rate suspension geometry unlike most traditional 4 link competition designs which have falling rate geometries. No other chassis available can obtain the same center ground clearance with a center of gravity anywhere near as low as the Stick. $220
Image
.
.
.
.
.
.
.
Complete TQ3 System with Rear Steer Installed ($65):
A New Traxxas TQ3 transmitter, receiver and crystal set with the rear steering kit already installed. A complete RTR (Ready-To-Run) radio system ready to be installed in your new crawler.
Image
.
.
.
.
.
.
TQ3 Rear Steering Kit ($10):
Convert your TQ3 to operate the rear steering of your crawler. Rear steering significantly improves crawling performance. Highly detailed instructions with photos and a three position spring return switch are included. Disassembly of your TQ3 and soldering are required.
Image
.
.
.
.
.
.
Clodbuster or Jugg to E-Maxx/T-Maxx Wheel Adapter Kit. Includes 4 adapters and 4 barrel nuts with washers. Works with stock, deep offset, or Jumbo Maxx wheels. $45
Image
.
.
.
.
.
.
G-Made Top Link Mounts (one set of two) ($29.99):
One of the best upper link mounts available. The unique design eliminates rotation of the top link post. Made of durable MC Nylon and aluminum. NOTE: The screw hole for mounting the upper links is for 4mm screws, most regular links use 3mm screws. These mounts have been tested by our staff using standard Traxxas rod ends with 3mm screws without problems.
Image
.
.
.
.
.
.
.
G-Made Brace Mount Set ($49.99):
These brace mount sets act as an axle tube brace, lower link mount, and shock mount. Great item to make your next crawler different from all the rest. Note: Bottom link mount hole is for 4mm screws, standard Traxxas rod ends use 3mm bolts. These mounts have been tested by our staff using standard Traxxas rod ends with 3mm screws without problems.
Image
.
.
.
.
.
.
Adjustable Motor Mounts - Clodbuster (pair). Set of two Thunder Tech Racing Adjustable Motor Mounts for the Tamiya Clodbuster. Allows the use of 6 tooth to 16 tooth pinions with no modifications to the stock Tamiya Clodbuster axle. Also includes two clear adhesive gear covers. $30
Image
.
.
.
.
.
.
Complete Unassembled Clodbuster Axles (pair). Set of two new complete unassembled Clodbuster axles. $145
Image
.
.
.
.
.
.
Monster Rod Ends - M4 10mm Ball & M5 10mm Rod End. Shown next to a standard Traxxas rod end below. Includes 20 each rod ends, 20 each ball, and 2 each aluminum spacer for top link bolts. Use 4mm hardware on the ball and 5mm hardware on the rod end. $29.99
Image

Image
.
.
.
.
.
.
.
Body Clips - 100 Each. $7.50
Image
.
.
.
.
.
.
.
Image

Post Reply
Users browsing this forum: No registered users and 1 guest